Product details
Product Introduction
Vertical impact crusher is a kind of forced crusher different from the common vertical composite crusher, cone crusher and roller crusher and grinding machines like ball mill, autogenous grinding and semi-autogenous grinding machines and traditional impact crusher and hammer crusher.
Working Principle
Materials fall freely into the rotary impeller from the upper part of the machine. Under the centrifugal force, they impact with other materials distributed around the impeller in an umbrella shape. Then, the vortex will be formed between the impeller and the casing for several times of impact, friction and crushing. At last, they will be discharged from the lower hopper. Closed-circuit is formed and the granularity of finished products is controlled by the screen equipment.
Performance Characteristics
1. Currently, it's a new machine for secondary and fine crushing as well as the one that is widely applied to replace the cone crusher, rolling machine and ball mill.
2. Novel and unique structure, stable operation.
3. Low energy consumption, high output and high size reduction ratio.
4. Small size, simple operation, convenient installation and maintenance.
5. It has shaping function with cubic products and high stacking density.
6. Materials can form protective cover to reduce the abrasion of the body to make it durable.
7. Some abrasive parts are made of hard and wear-resistant materials, featured by small size, lightness and convenient renewal.
Model
Model |
Content |
P |
Crusher |
L |
Vertical Impact |
Specification (Impeller Diameter, mm) |
Technical Parameter
Model |
Parameters |
|||||
Impeller Rotary Speed r/min |
Motor Power kw |
Feeding Granularity mm |
Discharging Granularity mm |
Volume t/h |
Reference Weight /t |
|
PL-550 |
2000~3000 |
30~55 |
≤30 |
≦5 Volume Proportion (25%~50%) |
15~35 |
~5300 |
PL-700 |
1500~2310 |
55~110 |
≤35 |
≦5 Volume Proportion (25%~50%) |
30~70 |
~8500 |
PL-850 |
1200~1620 |
110~180 |
≤50 |
≦5 Volume Proportion (25%~50%) |
75~120 |
~12400 |
PL-900 |
1200~1910 |
150~264 |
≤50 |
≦5 Volume Proportion (25%~50%) |
90~160 |
~13300 |
PL-1000 |
1000~1630 |
180~320 |
≤60 |
≦5 Volume Proportion (25%~50%) |
130~210 |
~17300 |
PL-1200 |
850~1350 |
320~440 |
≤60 |
≦5 Volume Proportion (25%~50%) |
180~320 |
~22500 |
Note 1: The volume is determined based on the following conditions: |
Instructions
1. Check whether there is ore bed inside the vortex crushing chamber through the peep hole. If there isn't, the materials in the chamber should be no more than 25mm. And the ore bed will be forced until materials can flow automatically.
2. Looking from the feeding inlet, the rotary direction of the impeller should be anticlockwise or the wiring should be adjusted.
3. The startup order of the crusher and the conveyor is as followed: discharging outlet belt conveyor → PL crusher → feeding belt conveyor. The crusher must be started with no load and then it can be fed after the machine runs orderly.
4. The feeding granularity is strictly in accordance with the specifications. It's not allowed for materials of larger than the specified size to enter into the crusher, or it will lead to the imbalance and over-abrasion of the impeller which will further cause the jam of the impeller runner and the center feed pipe. So it must be cleared in time if there are lumpy materials.
5. The feeding must be stopped when discharging belt conveyor stopped. Therefore, the conveyor and the feeding system interlock should be synchronous or it will lead to the damage of the impeller and destroying the engine.
6. The feeding must be even and continuous. If there is any heavy vibration and abnormal noise, it must be stopped to check instantly. After the clearing of fault, the machine can be restarted.
7. All access doors should be tightly sealed during the operation and the belt cover should be well installed.
http://www.zoomlegend.com/